Multiple Choice Identify the
choice that best completes the statement or answers the question.
|
|
1.
|
A mechanical power transmission system receives power from the
___________.
a. | driven device | c. | prime mover | b. | driver | d. | B and C |
|
|
2.
|
The purpose for having a clutch connecting two shafts together is to
___________.
a. | allow the two shafts to be disconnected while running | c. | allow for easier assembly and
disassembly of the drive system | b. | multiply the torque of the drive
shaft | d. | change the direction
of rotation |
|
|
3.
|
The three types of shaft-to-adjacent-shaft power transmission are
______________.
a. | belt drive, clutch and gear drive | c. | belt drive, chain drive and gear
drive | b. | clutch, direct coupling and gear drive | d. | flexible coupling, direct coupling, and sleeve
coupling |
|
|
4.
|
Some rules for safe dress to wear around machinery when it is running are
___________.
a. | wear safety glasses and gloves at all times | c. | wear bright colored
clothing | b. | wear tight fitting clothing and heavy duty shoes | d. | wear light weight, loose fitting
clothing |
|
|
5.
|
________________ may remove a lockout on the power source of a piece of
mechanical equipment.
a. | Only the instructor | c. | Only the person who installed the lockout | b. | Any two
people | d. | Any person familiar
with the mechanical equipment |
|
|
6.
|
A machine foundation should be designed to support the load of the machine,
maintain the alignment between coupled components, and ______________.
a. | be easily removed | c. | blend with the other foundations | b. | be light
weight | d. | absorb any vibration
created by the machine |
|
|
7.
|
An industrial machine foundation usually consists of _________________.
a. | asphalt | c. | solid concrete | b. | wooden beams | d. | existing floor
material |
|
|
8.
|
A spirit level can be used _____________.
a. | in the vertical or horizontal position | c. | only in the horizontal
position | b. | only in the vertical position | d. | in any position |
|
|
9.
|
The adjustable motor mount is used __________________.
a. | when it is routinely necessary to change the tention on a belt or chain
drive | c. | when it is necessary to change the size of the motor | b. | to vary the motor
speed | d. | to compensate for
wear on the motor bearings |
|
|
10.
|
The most common fastener used to attach a motor to a bedplate is a hex head bolt
with _______________.
a. | a lock washer and a nut | c. | two flat washers, a lock washer,
and a nut | b. | a flat washer, a lock washer, and a nut | d. | two flat washers, two lock washers, and a
nut |
|
|
11.
|
A ____________ bolt size should be selected to fit through a 1/2 inch hole in
the foot of a motor mount.
a. | 1/2 inch | c. | 9/16 inch | b. | 7/16 inch | d. | 1/4 inch |
|
|
12.
|
In addition to dress rules, another rule to follow with machinery is
_______________.
a. | to have someone else in the work area | c. | do not work on wet
floors | b. | enter a work area while the machine is running | d. | to keep tools out in the work area for easy
access |
|
|
13.
|
The grade of a bolt can be determined by ____________________.
a. | measuring the bolt diameter | c. | counting its threads per
inch | b. | measuring the bolt length and diameter | d. | the marking on the head of the
bolt |
|
|
14.
|
A soft foot condition on a motor mount should be corrected by
________________.
a. | shimming one foot only | c. | ending the soft foot on the motor base | b. | shimming all four
feet | d. | shimming two
diagonally opposite feet |
|
|
15.
|
A bedplate is a solid piece of metal usually made of __________________.
a. | copper | c. | brass | b. | steel | d. | cast iron |
|
|
16.
|
The device most often used to orient a surface so it is either parallel or
perpendicular to the ground is a ______________.
a. | measuring tape | c. | plum bob | b. | spirit level | d. | laser alignment
device |
|
|
17.
|
One revolution per second is equal to ______________.
a. | 1 RPM | c. | 60 RPM | b. | 1000 RPM | d. | 6 RPM |
|
|
18.
|
To measure motor RPM, the rubber-tipped shaft on a handheld tachometer must be
held against the ____________.
a. | end of the spinning motor shaft | c. | power cord while the motor is
running | b. | base or motor foot | d. | motor shaft, but only when the motor is stopped |
|
Matching
|
|
|
SEGMENT 1
Note: some answers may apply to
multiple questions.
a. | thermal | f. | should | b. | force;
motion | g. | true | c. | gears | h. | should not | d. | coupling | i. | false | e. | do not operate |
|
|
19.
|
The purpose of a mechanical transmission system is to transmit ________ and
________ from one device to another.
|
|
20.
|
Three methods of mechanical power transmission are electrical, ________, and
fluid.
|
|
21.
|
Two methods of axial power transmission commonly use are _________ and
clutches.
|
|
22.
|
Three methods of shaft-to-adjacent-shaft power transmission are belt drives,
chain drives, and ________ drives.
|
|
23.
|
Safety glasses ____________ (should/should not) be worn at all times.
|
|
24.
|
Long sleeves _________ (should/should not) be rolled up.
|
|
25.
|
Lockout/tagout devices __________ (should/should not) be used to lock out the
power switch.
|
|
26.
|
A tagout tag should clearly read _______.
|
|
27.
|
The only person who should remove a lockout/tagout from a powr source is the
person who installed it.
|
|
|
SEGMENT 2
a. | bubble | d. | absorb vibration | b. | perpendicularity | e. | structural steel | c. | bedplate |
|
|
28.
|
A foundation has three functions: support the load of the machine without
settling, maintain alignment between coupled components, and _________.
|
|
29.
|
A foundation for heavy equipment can be made from solid concrete, reinforced
concrete, or _________.
|
|
30.
|
A(n) _________ placed on a foundation provides a rigid, level surface for
mounting components.
|
|
31.
|
A spirit level is used to measure _______ and parallelism of a surface with the
ground.
|
|
32.
|
A spirit level has liquid filled tubes containing a(n) _______ and two
alignment marks.
|
|
|
SEGMENT 3
a. | flat | d. | foot | b. | shims | e. | diameter | c. | c-face
mount |
|
|
33.
|
The ____ mount consists of tabs or feet which are attached at the four corners
of the motor.
|
|
34.
|
A(n) _________ washer makes sure that the bolt will not pull through the
mounting hole.
|
|
35.
|
When selecting a fastener to mount a motor, the nut thickness should be equal
to the ________ of the bolt’s threads.
|
|
36.
|
________ are placed under the mounting feet of a motor as part of the leveling
process.
|
|
37.
|
The ________ mount is used to mount the driven component directly to the motor
face.
|
|
|
SEGMENT 4
Note: some answers may apply to
multiple questions.
a. | photo | c. | revolutions per
minute | b. | speedometer | d. | tachometer |
|
|
38.
|
The rotational speed of a motor is measured in __________.
|
|
39.
|
The device that is most often used to measure motor speed is the
______.
|
|
40.
|
A handheld mechanical tachometer works in much the same manner as the ______ in
a car.
|
|
41.
|
A(n) ___________ tachometer determines motor shaft speed by counting the number
of times a piece of reflective tape passes through the light.
|
|
42.
|
A(n) ________ tachometer has an interal gear system that converts the rotating
motion of a shaft into a reading on a dial indicator.
|