Multiple Choice Identify the
choice that best completes the statement or answers the question.
|
|
1.
|
The potential difference between two points in a circuit is called
___________.
a. | current | c. | resistence | b. | voltage | d. | none of the
above |
|
|
2.
|
The units of measurement for voltage is the ___________.
|
|
3.
|
A known reference point in an electrical circuit is called a
______________.
a. | ground | c. | negative | b. | zero reference | d. | positive |
|
|
4.
|
A(n) ______________ is a measurement device used to measure voltage.
a. | ohmmeter | c. | voltmeter | b. | multimeter | d. | ammeter |
|
|
5.
|
A multimeter is a multipurpose device that can measure ________________.
a. | voltage and resistance | c. | resistance and current | b. | voltage and
current | d. | voltage, current
and resistance |
|
|
6.
|
The amount of voltage that is used by each load depends on the _____________ of
each load.
a. | drop | c. | amps | b. | continuity | d. | resistance |
|
|
7.
|
An ammeter is used to measure _____________.
a. | current | c. | voltage | b. | resistance | d. | temperature |
|
|
8.
|
Resistance is measured in units of _________.
a. | volts | c. | ohms | b. | watts | d. | amps |
|
|
9.
|
If a wire has continuity, it ____________
a. | cannot conduct current | c. | cannot be used in a circuit | b. | will have almost no
resistance | d. | has an
open |
|
|
10.
|
A _____________ circuit is one in which there is only one path for current to
travel.
a. | complex | c. | parallel | b. | series | d. | closed |
|
|
11.
|
In a(n) ___________ circuit, the voltage available to each branch is equal to
the source voltage.
a. | parallel | c. | short | b. | series | d. | open |
|
|
12.
|
Current is measured in units of _________.
a. | amps | c. | ohms | b. | volts | d. | pascals |
|
|
13.
|
To measure current through a component, the ammeter must be connected in
____________ the component.
a. | across | c. | in series with | b. | in parallel with | d. | withour |
|
|
14.
|
Current in a(n) _____________circuit is divided among the branches of the
circuit.
a. | series | c. | open | b. | parallel | d. | short |
|
|
15.
|
A(n) _____________ is sed to measure resistance.
a. | ohmmeter | c. | voltmeter | b. | ammeter | d. | flowmeter |
|
|
16.
|
Which of the following statements is not true about measuring the resistance of
a component that is connected in a circuit.
a. | Turn off the power supply | c. | Make sure the power supply is
on. | b. | Disconnect one of the component leads from the circuit. | d. | Connect the leads across the
component. |
|
|
17.
|
When leads are connected in series, their individual resistanced are
____________
a. | multiplied | c. | subtracted | b. | divided | d. | added |
|
Matching
|
|
|
Segment 1
a. | Volts | e. | Voltage | b. | Digital Multimeter | f. | current | c. | ground | g. | lower | d. | V |
|
|
18.
|
__________ is the existence of a potential difference between two points in a
circuit.
|
|
19.
|
Voltage is measured in units called _________.
|
|
20.
|
________ is the abbreviation symbol used for voltage in equations.
|
|
21.
|
The measurement readings of a(n) _________ are much easier to read than an
analog multimeter.
|
|
22.
|
The black lead from the negative (common) terminal of the DMM should be
connected to the point with the _____ potential in the circuit.
|
|
23.
|
The three basic units that can be measured using a multimeter are Voltage,
________, and resistance.
|
|
24.
|
A(n) _________ is a common connection point, or a known reference point, in an
electrical circuit.
|
|
|
Segment 2
a. | parallel | d. | branch | b. | voltage | e. | divided | c. | series | f. | ground |
|
|
25.
|
There is only one path for current to travel in a _______ circuit.
|
|
26.
|
A ________ circuit has more than one path for current to flow.
|
|
27.
|
In a series circuit, the total voltage supplied by the power supply is _______
among the loads.
|
|
28.
|
The voltage drop across any component is the difference in voltage referenced
to __________ between the two terminals of the component.
|
|
29.
|
When a parallel circuit is connected to a constant voltage source, the same
amount of voltage is available to each _______ of the circuit.
|
|
30.
|
Most AC wiring circuits in buildings use parallel circuits so the loads can all
receive the same _________.
|
|
|
Segment 3
a. | Negative | d. | Series | b. | Amperes | e. | Parallel | c. | A |
|
|
31.
|
Current is measured in units called _________.
|
|
32.
|
_____ is the abbreviation symbol for current.
|
|
33.
|
When measuring current, the ammeter must be connected in __________ with the
components of the circuit.
|
|
34.
|
The current in a series circuit flows from the positive terminal of the supply
to the ___________ terminal through each component in a circuit.
|
|
35.
|
The current in a(n) ____________ circuit is divided among the branches of the
circuit.
|
|
|
Segment 4
a. | continuity | d. | W | b. | disconnect | e. | ohms | c. | across | f. | power source |
|
|
36.
|
Resistance is measured in units called __________.
|
|
37.
|
The symbol for ohm is ______.
|
|
38.
|
Since all electrical components in a circuit are connected with a conductor of
some kind, the conductor must have _________ or the circuit will not operate.
|
|
39.
|
A continuity tester is composed of a (n) __________ and a sounding
device.
|
|
40.
|
When measuring resistance, the user should measure __________ the
component.
|
|
41.
|
When measuring the resistance of a component in a circuit, the user should
______________ one side of the component from the circuit.
|